Timber Engineering Calculator

Timber Engineering Calculator contains 87 calculators and converters, that can quickly and easily calculate and convert different timber and civil engineering parameters. Automatic & accurate calculations and conversions with every unit and value Changes. * Available in Metric and Imperial Units * * Available in English, Français, Español, Italiano, Deutsch, Português & Nederlands * Timber Engineering Calculator contains following 55 Calculators: • Area of Section (Rectangular and Square Beam) • Moment of Inertia (Rectangular and Square Beam) • Distance from Axis to Extremities of Section (Rectangular and Square Beam) • Radius of Gyration (Rectangular and Square Beam) • Section Modulus (Rectangular and Square Beam) • Maximum Fiber Stress (Rectangular Timber Beam) • Maximum Fiber Stress using Section Modulus (Rectangular Timber Beam) • Horizontal Shearing Stress (Rectangular Timber Beam) • Horizontal Shearing Stress (Rectangular Timber Beam with a notch in the lower face at the end) • Modified Total End Shear (Concentrated Loads) • Modified Total End Shear (Uniform Loading) • Allowable Unit Stress on Timber Columns (Single Piece of Lumber/Group of Pieces glued together) • Allowable Unit Stress on Timber Columns (Square/Rectangular Cross Section) • Allowable Unit Stress on Timber Columns (Circular Cross Section) • Allowable Unit Compressive Stress (Load is at an angle to the grain) • Allowable Stress - Rectangular Section (National Design Specification) • Allowable Compressive Stress inclined to grain (Hankinson's Equation) • Extreme-Fiber Bending - Adjusted Design Value • Tension - Adjusted Design Value • Shear - Adjusted Design Value • Compression perpendicular to the grain - Adjusted Design Value • Compression parallel to the grain - Adjusted Design Value • End grain in bearing parallel to the grain - Adjusted Design Value • Modulus of Elasticity - Adjusted Design Value • Size Factor • Volume Factor (Southern Pine) • Volume Factor (Other Species) • Radial Stress induced by a Bending Moment • Curvature Factor • Bearing Area Factor • Slenderness Ratio for Beams • Allowable Withdrawal Load (Nails and Spikes penetration) • Total Allowable Lateral Load - Group I, II, III, IV Wood (Nails and Spikes penetration) • Allowable Withdrawal Load (Threaded portion of a Wood Screw penetration) • Total Allowable Lateral Load - Group I, II, III, IV Wood (Wood Screws penetration) • Bolts - Adjusted Design Value for Lateral Loading • Split-Ring and Shear-Plate Connectors - Adjusted Value for Loading Parallel to Grain • Split-Ring and Shear-Plate Connectors - Nominal Value for Loading Normal to Grain • Nails and Spikes - Adjusted Design Value for Withdrawal • Nails and Spikes - Adjusted Design Value for Lateral Loading • Wood Screws - Adjusted Design Value for Withdrawal • Wood Screws - Adjusted Design Value for Lateral Loading • Lag Screws - Adjusted Design Value for Withdrawal • Lag Screws - Adjusted Design Value for Lateral Loading • Metal Plate Connectors - Adjusted Design Value for Lateral Loading • Drift Bolts and Drift Pins - Adjusted Design Value for Withdrawal • Drift Bolts and Drift Pins - Adjusted Design Value for Lateral Loading • Spike Grids - Adjusted Design Value for Lateral Loading • Stress and Deflection Factor (Ponding) Timber Engineering Calculator contains following 32 Converters: • Acceleration • Angle • Area • Density • Energy/Work • Flow Rate (Mass) • Flow Rate (Volume) • Fluid • Force • Frequency • Hardness • Length • Mass • Metric Weight • Metrology • Moment of Force • Moment of Inertia • Prefixes • Pressure • Radiation • Specific Heat Capacity • Specific Volume • Temperature • Thermal Conductivity • Thermal Expansion • Time • Torque • Velocity • Viscosity (Dynamic) • Viscosity (Oil & Water) • Viscosity (Kinematic) • Volume Most Comprehensive Timber Engineering Calculator