Elevator Mechanic Exam Prep Live

ELEVATOR MECHANIC EXAM PREP: PASS YOUR STATE LICENSING EXAM The only exam prep app built for elevator mechanic state licensing exams. Your exam tests ASME A17.1 Safety Code, NEC Article 620 electrical requirements, OSHA standards, and mechanical systems. This app covers all of it. TRACTION VS HYDRAULIC COMPARISON Traction elevator: steel ropes and sheave driven by electric motor. Geared traction for slower speeds, gearless for high-rise. Counterweight reduces motor load. No practical speed limit. Hydraulic elevator: pump, jack, and oil raise the car. Gravity controls lowering. Types: in-ground direct acting, holeless, roped hydraulic. Maximum travel approximately 50 feet. Safety devices compared side by side including governor and safeties (traction) vs lowering valve and rupture valve (hydraulic), buffer types, and ASME A17.1 inspection intervals. ASME A17.1 CODE REFERENCE Pit: minimum 2-foot depth, lighting at top of ladder, stop switch within 2 feet, ladder required if pit exceeds 35 inches. Machine room: minimum 7-foot headroom, temperature 50 to 90 degrees F, disconnect switch within sight of equipment. Hoistway: fire-resistive construction, no combustible materials. Inspection intervals: periodic inspection annually, safety tests and governor test every 5 years. Source: ASME A17.1 Safety Code for Elevators and Escalators — https://www.asme.org/codes-standards/find-codes-standards/safety-code-for-elevators-and-escalators SAFETY DEVICE GUIDE Governor: centrifugal, activates at overspeed, trips car safety. Car safety: grips guide rails. Instantaneous for lower speeds, progressive for higher speeds. Buffer: oil (traction) or spring (hydraulic). Door interlock: prevents movement unless hoistway door is locked. Pit stop switch: breaks control circuit. 1,000+ PRACTICE QUESTIONS ELECTRICAL THEORY AND NEC (30%): Three-phase power, motor theory, motor control circuits, NEC Article 620, grounding and bonding, branch circuits, GFCIs in machine rooms. Source: NFPA 70 National Electrical Code (NEC) — https://www.nfpa.org/codes-and-standards/nfpa-70-standard-development/70 ASME A17.1 CODE (25%): Pit, machine room, and hoistway requirements, car enclosure, inspection and test intervals, emergency operation, accessibility. MECHANICAL SYSTEMS (25%): Traction components (sheave, wire ropes, counterweight, guide rails), hydraulic components (pump, jack, control valve, cylinder), brake systems, lubrication. SAFETY DEVICES (10%): Governor and overspeed settings, safety types, buffer types, door interlock, testing intervals. OSHA AND SAFETY (10%): OSHA 1926 Subpart R, lockout and tagout, fall protection in hoistways, confined space for pits. Source: OSHA 1926 Subpart R — https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926SubpartR Every question includes a detailed explanation with ASME A17.1 section and NEC article references. FREE: 5 questions per day, traction vs hydraulic comparison, safety device overview. No account required. MONTHLY ($9.99): Unlimited questions, all tools, 3-day free trial. ANNUAL ($24.99): Save over 75 percent. Best value. LIFETIME ($49.99): One payment. Permanent access. PASS PROMISE: 80% average, active subscription 3 months, still do not pass: 4 months extended free. voltexam.com/pass-promise Not affiliated with NEIEP, IUEC, ASME, or any state elevator licensing board. Code references are for educational exam preparation only. Privacy Policy: https://www.voltexam.com/privacy Terms of Service: https://www.voltexam.com/terms This app is an independent study tool and is not affiliated with, endorsed by, or produced by ASME, ICC, NEC/NFPA, OSHA, or any government agency or licensing board.